![c debugging questions with answers pdf c debugging questions with answers pdf](https://freeprintablejadi.com/wp-content/uploads/2019/07/printable-50-question-answer-sheet-pdf-multiple-choice-a-b-c-d-free-printable-bubble-answer-sheets.jpg)
For a line AB a) the forebearing of AB and back bearing of AB differ by 180° b) the forebearing of AB and back bearing of BA differ by 180° c) both (a) and (b) are correct. In the prismatic compass a) the magnetic needle moves with the box b) the line of the sight does not move with the box c) the magnetic needle and graduated circle do not move with the box d) the graduated circle is fixed to the box and the magnetic needle always remains in the N-S direction Ans: c 20. If the true bearing of a line AB is 269° 30′, then the azimuth of the line AB is a) 0° 30′ b) 89° 30′ c) 90° 30′ d) 269° 30′ Ans: c 19. d) The maps prepared by national survey departments of any country are based on true meridians. c) The true meridians converge to a point in northern and southern hemispheres. b) The true meridian at any place is not variable. a) The true meridians at different places are parallel to each other. The length of a chain is measured from a) centre of one handle to centre of other handle b) outside of one handle to outside of other handle c) outside of one handle to inside of other handle ĭ) inside of one handle to inside of other handle Ans: b 17. For accurate work, the steel band should always be used in preference to chain because the steel band a) is lighter than chain b) is easier to handle c) is practically inextensible and is not liable to kinks when in use d) can be easily repaired in the field Ans: c 16. The maximum tolerance in a 20 m chain is a) ☒ mm b) ☓ mm c) ±5 mm d) ☘ mm Ans: c 15. If the length of a chain is found to be short on testing, it can be adjusted by a) straightening the links b) removing one or more small circular rings c) closing the joints of the rings if opened out d) all of the above Ans: a 14. Which of the following is not used in measuring perpendicular offsets ? a) line ranger b) steel tape c) optical square d) cross staff Ans: a 13. Normal tension is that pull which a) is used at the time of standardising the tape b) neutralizes the effect due to pull and sag c) makes the correction due to sag equal to zero ĭ) makes the correction due to pull equal to zero Ans: b 12. Cross staff is an instrument used for a) measuring approximate horizontal angles b) setting out right angles c) measuring bearings of the lines d) none of the above Ans: b 11. The correction for sag is a) always additive b) always subtractive c) always zero d) sometimes additive and sometimes subtractive Ans: b 10. The permissible error in chaining for measurement with chain on rough or hilly ground is a) 1 in 100 b) 1 in 250 c) 1 in 500 d) 1 in 1000 Ans: b 9. Which of the following methods of offsets involves less measurement on the ground? a) method of perpendicular offsets b) method of oblique offsets c) method of ties d) all involve equal measurement on the ground Ans: a 8. Which of the following angles can be set out with the help of French cross staff? a) 45° only ī) 90° only c) either 45° or 90° d) any angle Ans: cħ. The allowable length of an offset depends upon the a) degree of accuracy required b) method of setting out the perpendiculars and nature of ground c) scale of plotting d) all of the above Ans: dĮngineering Questions Engineering Questions 4,405 likesīe the first of your friends to like thisĮngineering intervie Follow 619 followersĦ. The angle of intersection of the two plane mirrors of an optical square is a) 30° b) 45° c) 60° d) 90° Ans: b 5.
![c debugging questions with answers pdf c debugging questions with answers pdf](https://tests4geeks.com/content/img/smp/c-sharp-test-questions.png)
For a well-conditioned triangle, no angle should be less than a) 20° b) 30° c) 45° d) 60° Ans: b 4. A metallic tape is made of a) steel b) invar c) linen d) cloth and wires Ans: d 3. Distance of the follower from the starting point is a) 4 chains Ģ. leader of the party has 4 arrows in his hand while the follower has 6. During chaining along a straight line, the. SURVEYING Multiple Choice Questions and Answers :1. Want Sand Makin Machine? - Sand Maker: 50-1000t/ Complete Sand Crushing Plant, VSI Sand Crusher Used In Construction. Get 9 Exemptions from the ACCA Certi cation Home » SURVEYING Questions and Answers » 110 TOP MOST SURVEYING Interview Questions and Answers – Civil Engineering Objective Type Questionsġ10 TOP MOST SURVEYING Interview Questions and Answers – Civil Engineering Objective Type Questions Online Accounting Diploma UNICAF Scholarship Diploma in Accounting. HOME Interview Questions MCQs *LAB VIVA CLASS NOTES SEMINAR TOPICS ONLINE TEST GATE IIT JEE CAT
C DEBUGGING QUESTIONS WITH ANSWERS PDF PDF
110 TOP SURVEYING Multiple Choice Questions with Answers PdfĮngineering Interview Engineering interview questions,multiple choice questions,objective type questions,seminor topics,lab viva questions and answers ,online quiz test pdf free download for freshers.